Jung switch actuator Secure KNX UP

• Nominal voltage: DC 21-32 V SELV
• Switching current: 16 A
For 230011SU:
• Switching of electrical loads via relay contact
• Reading of switching states of installation switches or buttons and other floating contacts at inputs 1-3
For 230021SU:
• Switching of electrical loads via relay contacts with common reference potential
• Switching of electrically operated blinds, roller shutters, awnings and similar

• Ambient temperature: -5 ... +45°C
• Dimensions (W x H x D): 48 x 50 x 28 mm
• Commissioning mode: S-mode
• KNX current consumption: 5 - 18 mA
• KNX connection: Connection terminal on control line
Outputs:
• Connection type: Screw terminals
• Screw terminals: AC 250 V ~
• Fluorescent lamps: 16 AX
• Inrush current 200 µs: max. 800 A
• Inrush current 20 ms: max. 165 A
Connected load:
• Ohmic load: 2500 W
• Capacitive load: max. 16 A (140 µF)
• Motors: 1380 VA
• Incandescent lamps: 2300 W
• HV Halogen lamps: 2300 W
• HV LED lamps: max. 400 W
• LV halogen lamps with:
- Electronic transformers: 1500 W
- Inductive transformers: 1200 VA
• Compact fluorescent lamps:
- Uncompensated: 1000 W
- Parallel-compensated: 1160 W / 140 µF
• Reduction in connected load:
- Per 5°C exceeding 25°C: -10%
- For installation in wooden or drywall: -15%
- For installation in multiple combinations: -20%
Connection:
• Connection type: Screw terminals
- Single-wire: 1 x 0.5 ... 4 mm²
- Fine stranded without ferrule: 1 x 0.5 ... 4 mm²
- Fine stranded with ferrule: 1 x 0.5 ... 2.5 mm²
Inputs:
• Control cable: YY6x0.6 (pre-assembled)
• Input type: potential-free
• Number: 3
• Total length of extension cable: max. 10 m
• Cable type: J-Y(St)Y
• Interrogation voltage extension inputs: approx. 5 V

• Signal evaluation of condensation sensors (item no.: BTS 01) and leakage sensors (item no.: LES 01) at inputs 1...3
• Recording of temperature values via NTC temperature sensors (item no.: FF NTC, FF 7.8) at input 3
• Mounting in appliance box with dimensions according to DIN 49073
• Output can be operated via KNX telegrams or extension inputs
• Three extension unit inputs for connecting potential-free contacts or condensation/leakage sensors. NTC temperature sensor can be connected to input 3
• Supply via bus, no additional supply voltage required
• KNX Data Secure compatible from ETS 5.7.3
• Updateable with ETS Service app

• Switch operation properties:
- Normally open or normally closed operation
- Logic operation and positive drive function
- Central switching function
- Time functions: Switch-on, switch-off delay, staircase light switch with pre-warning function
- Scene function
- Operating hours counter

• Properties of extension unit input:
- Operating functions Switches, Dimmers (incl. colour temperature dimming), blind control, value transmitter (1-byte, 2-byte, 3-byte and 6-byte incl. RGBW and colour temperature presets), scene extension unit etc.
- Disable function
- Debounce time adjustable

• Logic properties:
- Logic gate
- Converter (conversion)
- Blocking element
- Comparator
- Limit value switch

• Blind operation properties:
- Suitable for AC motors 110 ... 230 V
- Operating modes "blind with slat", "roller shutter/awning", "ventilation flap/roof window"
- Blind position and slat position directly controllable
- Feedback of movement status, blind position and slat position
- Forced position through higher-level control
- Safety function: rain alarm, frost alarm, 3 independent wind alarms
- Sun protection function with automatic heating/cooling function
- Locking function (lock-out protection)