Mechanic’s tool kit, metric, 179-piece

consisting of:
• 1/4” 2-component reversible ratchet, 129 mm
• 1/4” square plug-in handle: 140 mm
• 1/4” socket wrench insert, external hex: Size 4/4.5/5/5.5/6/7/8/9/10/11/13
• 1/4” socket wrench extension: 97 mm
• 1/4” cross-handle: 115 mm
• 1/4” cardan joint: 38 mm
• 1/2” 2-component reversible ratchet, 270 mm
• 1/2” socket wrench insert, external hex: Size 8/10/11/12/13/14/15/16/17/18/19/21/22/23/24/26/27/28/30/32
• 1/2” hex socket wrench insert: 5/6/7/8/9/10/12/14/17
• 1/2” socket wrench extension: 125, 250 mm
• 1/2” cardan joint: 72 mm
• 1/2” cross-handle: 292 mm
• 1/2” screw releaser: 123 mm
• 5/16” slotted bit: 5.5/6.5/8/12
• 5/16” hex socket bit: 4/5/6/8/10
• 5/16” Phillips bit: PH2/PH3/PH4
• 5/16” Torx® socket bit: T27/T30/T40/T45
• 5/16” connector for bits: 5/16” hex x 1/2” square + 5/16” hex x 1/4” square
• Double ring spanner, offset: Size 6x7/8x9/10x11/12x13/14x15/16x17/18x19/20x22/21x23/24x27/25x28/30x32
• Open-ended spanner: Size 6x7/8x9/10x11/12x13/14x15/16x17/18x19/20x22/21x23/24x27/25x28/30x32
• Angled screwdriver, internal hex: Size 2/2.5/3/4/5/6/8/10
• Adjustable spanner 8”: 205 mm
• Warding file set, 6-piece
• Screwdriver, slotted: 3/4/5.5/6.5/8/10
• Screwdriver, slotted, short: 6.5
• Screwdriver, Phillips: PH1/PH2/PH3
• Screwdriver Phillips, short: PH1/PH2
• Pozidriv screwdriver: PZ1/PZ2
• Ball-peen hammer: 500 g
• Centre punch: ø 4mm x 120 mm
• Drift punch: ø 3 x 120 mm / ø 5 x 120 mm
• Flat chisel: 12 x 125 mm, 16 x 150 mm, 22 x 200 mm
• Cross chisel: 125 mm
• Pin punch, length 150 mm: ø 2/3/4/5/6/8 mm
• Universal pliers: 256 mm
• Power combination pliers: 180 mm
• Needle nose pliers: 160 mm
• Needle nose pliers, angled: 160 mm
• Power side cutter: 160 mm
• Power front cutter: 160 mm
• Pipe tongs 1 1/2”: 430 mm
• Gripping pliers: 260 mm
• External locking ring pliers form A: 10-25 mm/19-60 mm
• External locking ring pliers form B: 10-25 mm/19-60 mm
• External locking ring pliers form C: 12-25 mm/19-60 mm
• Internal locking ring pliers form D: 12-25 mm/19-60 mm
• Thread file, thread pitch 0.8/1.0/1.25/1.5/1.75/2.0/2.5/3 mm: 230 mm
• Rolling head pry bars: 400 mm
• PUK® saw: 290 mm
• Hacksaw
• Magnetic lifter, flexible: 520 mm
• Three-square hollow scraper: 200 mm
• Callipers: 213 mm
• Scriber: 250 mm
• Cable knife: 195 mm
• Tape measure: 3 m
• Screwdriver set: M3-M45
• Soft-faced hammer, no recoil: 800 g
• Workshop file, flat: 200 mm
• Workshop file, triangular: 200 mm
• Workshop file, round: 200 mm
• Workshop file, half-round: 200 mm
• Tin snips, right-hand cut: 260 mm
• Square awl: 100 m
• Oil spray can 300 ml